Immergas Appliance Repair in Brinnington & Stockport Central

What does the 425 error mean on an Immergas heat pump?

The 425 error on an Immergas heat pump indicates a supply voltage phase loss. This error applies only to three-phase models and indicates one of the electrical supply phases has been lost. Switch off the heat pump at the isolator switch immediately. Do not attempt to restart. Contact a qualified electrician to check the three-phase electrical supply. Operating with a missing phase can cause serious damage to the compressor motor.

What does the 202 error mean on an Immergas heat pump?

The 202 error on an Immergas heat pump indicates a sustained communication error between the control kit and outdoor unit lasting more than three minutes. Switch off the heat pump at the isolator switch for five minutes. Switch back on and monitor for the error. If communication is not restored, contact a qualified technician. Do not repeatedly reset the unit as this will not resolve a wiring or component fault.

What does the 25 error mean on an Immergas boiler?

The 25 error on an Immergas boiler indicates a block due to flue gas temperature gradient intervention. The boiler has detected a rapid increase in flue gas temperature, which may indicate a blocked pump, insufficient water in the heat exchanger, or other circulation problems. Switch off the boiler at the electrical supply. Allow the boiler to cool down completely for a minimum of 60 minutes. Check that all radiator valves are open and system pressure is correct. Press the reset button once after cooling. If the error recurs frequently, contact a qualified technician.

What does the 24 error mean on an Immergas boiler?

The 24 error on an Immergas boiler indicates a push button control panel anomaly. The main circuit board has detected a fault with the user control panel. Switch off the boiler at the electrical supply. Wait 30 seconds and switch back on to reset. If normal conditions are restored, the boiler should restart automatically without requiring a manual reset. If the error persists, contact a qualified technician for control panel diagnosis.

What does the 320 error mean on an Immergas heat pump?

The 320 error on an Immergas heat pump indicates an OLP sensor error. The overload protection sensor on the compressor has detected a fault. Switch off the heat pump at the isolator switch. Do not attempt to reset repeatedly. Contact a qualified technician with F-Gas certification for compressor and sensor inspection. This protection system prevents compressor damage from electrical overload.

What periodic maintenance does my Immergas heat pump need?

Periodic maintenance includes visually checking for water leaks or oxidation on connections, verifying that safety devices have not been tampered with, and ensuring the outdoor unit remains free of debris. Check that drainage for condensate and defrost water is clear.

How do I switch my Immergas boiler between summer and winter mode?

Use the mode selector on the control panel or remote control to switch between modes. In summer mode, the boiler provides domestic hot water only and central heating is disabled. In winter mode, both domestic hot water and central heating are enabled. If using a CAR remote control, turn the main selector to the desired position. The display will show the current mode. Some models use icons: a sun or umbrella symbol for summer mode and a snowflake symbol for winter mode.

At what temperature should I store hot water to prevent bacteria growth?

If your Immergas system includes a hot water storage cylinder, the water should be stored at a minimum of 60 degrees Celsius to prevent the growth of harmful bacteria including Legionella. Water at taps should reach at least 50 degrees Celsius within one minute of running. Some Immergas systems include an anti-legionella function that periodically raises the stored water temperature automatically. This does not apply to combi boilers which heat water on demand without storage.

Why does my Immergas boiler keep losing pressure?

Frequent pressure loss typically indicates a problem that requires professional diagnosis. Common causes include small leaks in the heating system pipework or radiator valves, a faulty pressure relief valve, or a problem with the expansion vessel. If you need to repressurise more than once every few months, contact a qualified technician to identify and repair the underlying cause. Do not ignore persistent pressure loss as it can lead to boiler damage or system failure.

How do I repressurise my Immergas boiler?

Locate the filling loop beneath or near your boiler. Open both valves slowly to allow cold mains water into the system while watching the pressure gauge. When it reaches between 1.0 and 1.2 bar, close both valves securely.