Immergas Appliance Repair in Edgeley

What does the 37 error mean on an Immergas boiler?

The 37 error on an Immergas boiler indicates low power supply voltage. The electrical supply to the boiler has dropped below acceptable operating limits. Check that other electrical appliances in your home are working normally. If other appliances are also affected, there may be a general power supply issue in your area. Contact your electricity supplier. If only the boiler is affected, switch off the boiler and contact a qualified electrician to check the electrical supply circuit and connections to the boiler.

What does the 554 error mean on an Immergas heat pump?

The 554 error on an Immergas heat pump indicates a coolant leak has been detected in the refrigerant circuit. This is a serious fault requiring immediate professional attention. Switch off the heat pump at the isolator switch immediately. Do not attempt to reset or restart the unit. Contact a qualified technician with F-Gas certification immediately. Refrigerant leaks must be repaired by certified professionals and the system recharged before operation can resume.

What does the 27 error mean on an Immergas boiler?

The 27 error on an Immergas boiler indicates insufficient water circulation in the heating circuit. The boiler has detected inadequate water flow, which may cause overheating. Switch off the boiler at the electrical supply. Check that all radiator valves are fully open. Verify the system pressure is between 1.0 and 1.5 bar on the gauge. Listen for the circulation pump operating when you switch the boiler back on. If the pump is silent or making unusual noises, or if the error persists, contact a qualified technician to inspect the pump and system for blockages.

What does the 20 error mean on an Immergas boiler?

The 20 error on an Immergas boiler indicates a parasite flame block. The flame detection system is sensing a flame signal when the boiler should not be firing, which could indicate a leak in the detection circuit or a flame control unit anomaly. If you smell gas, do not operate any switches, ventilate the area if safe to do so, leave the property immediately, and call the gas emergency service from outside. If there is no gas smell, switch off the boiler at the electrical supply and do not attempt to restart. Contact a Gas Safe registered engineer immediately for inspection.

What does the 44 error mean on an Immergas boiler?

The 44 error on an Immergas boiler indicates a block due to maximum time with partial gas valve opening. The gas valve has been in a partially open state for longer than the permitted safety time. If you smell gas, do not operate any switches, ventilate the area if safe to do so, leave the property immediately, and call the gas emergency service from outside. If there is no gas smell, switch off the boiler at the electrical supply. Do not attempt to reset. Contact a Gas Safe registered engineer immediately for gas valve inspection and repair.

Does my Immergas heat pump have antifreeze protection?

Yes, Immergas heat pumps include automatic antifreeze protection that activates when outdoor temperatures drop below freezing. This prevents damage to the system and water circuits.

What is weather compensation on my Immergas heat pump?

Weather compensation automatically adjusts the flow temperature based on outdoor conditions. When it is colder outside, the system increases the water temperature to provide more heat. When it is warmer, the temperature is reduced to save energy. The system uses an outdoor temperature sensor to monitor conditions. This feature improves efficiency by preventing the heat pump from working harder than necessary. The heating curve settings are typically configured by your installer to suit your home.

What periodic maintenance does my Immergas heat pump need?

Periodic maintenance includes visually checking for water leaks or oxidation on connections, verifying that safety devices have not been tampered with, and ensuring the outdoor unit remains free of debris. Check that drainage for condensate and defrost water is clear.

How do I repressurise my Immergas boiler?

Locate the filling loop beneath or near your boiler. Open both valves slowly to allow cold mains water into the system while watching the pressure gauge. When it reaches between 1.0 and 1.2 bar, close both valves securely.

Does my Immergas boiler have a condensate drain that needs attention?

Yes, all Immergas condensing boilers produce condensate that drains away through a dedicated pipe. The condensate drain trap and pipe should be checked as part of annual servicing to ensure they are clear and draining correctly. A blocked condensate drain can cause the boiler to lock out. During very cold weather, external condensate pipes can freeze. If this happens, the boiler will stop working. Contact a qualified technician for assistance as attempting to thaw frozen pipes incorrectly can cause damage.